PIR-T15AM Triple Mirror Passive Sensor, Wide Angle Protection

Home page » Product » Alarm System » PIR & Magnetic Switch (Takex- Japan) » PIR-T15AM - Đầu báo hồng ngoại ngoài trời quét thể tích

Description

PIR-T15AM Triple Mirror Passive Sensor, Feature:
TRIPLE MIRROR OPTICAL SYSTEM
The unique combination of triple mirrors and three twin pyros enable 4 selectable operation modes including low position, high position, pet, and high density; for distances up to 49’ (15m) from a mounting height of 6.6’ (2m) to 20’ (6m), throughout a full 80°.

OPTIMISED DETECTION AREA
The triple mirror optical system features a geared mirror array allowing detection patterns to be dynamically optimised for maximum performance depending on the chosen mounting height and operation mode.

PET IMMUNITY
Independently controlled pyro devices in each optical unit use intelligent signal processing to eliminate nuisance alarms from small animals, and a dedicated pet operation mode further enhances discrimination performance against medium-sized animals.

PRECISE AREA ADJUSTMENT
Precise detection area adjustment is made possible by projecting coloured LED’s onto the surface of each mirror -visible only from inside the detection zone during the alignment process allowing sensitive zones to be fine-tuned to individual site requirements as desired. Unnecessary areas can be cancelled using the supplied area-masking sheet.

DESIGN CONSCIOUS
The PIR-T15AM’s unassuming design allows it to blend discreetly into any industrial, commercial or domestic environment, and the internally adjustable optic system helps to conceal the detection area and direction for more secure protection.

OTHER FUNCTIONS
Enhanced features including creep zone detection, near area cancellation, dual outputs, lightning surge protection and anti masking make the PIR-T15AM a key addition to the TAKEX family of high performance intrusion detection sensors.

Model	PIR-T15AM(G)
Detection system	Passive infrared
Detection area	Wide angle (80°) detection Detection distance: 49’(15m), 108 rays (54 pairs)
Power supply	9 to 28V DC (non-polarity)
Current consumption	Max. 50mA
Alarm output	Contact method : Dry semi-conductor contact, N.C./N.O. selectable Contact operation : One-shot operation when detecting intrusion Continuous output in the event of cover monitor error Continuous output in the event of alignment position error Continuous output in the event of self diagnosis error Continuous output in the event of power voltage error Continuous output in the event of long-term diagnosis error Contact rating : 24V (AC/DC) 0.25A (resistive load) (built-in contact protective resistor 3.3Ω)
External output	Contact method : Dry semi-conductor contact N.O. Contact operation : One-shot operation/Off delay operation selectable when detecting intrusion Contact rating : 24V (AC/DC) 0.25A (resistive load) (built-in contact protective resistor 3.3Ω)
Tamper output	Contact method : Dry mechanical contact, N.C. Contact operation : Continuous output Contact rating : 24V (AC/DC) 0.1A (resistive load) (built-in contact protective resistor 3.3Ω
Anti-masking output	Contact method : Dry semi-conductor contact N.C. Contact operation : Continuosly output when an object is placed in front of the lens (until nomal recovery) Contact rating : 24V (AC/DC) 0.25A (resistive load) (built-in contact protective resistor 3.3Ω)
Alarm LED	Red LED : Blinks* during warm up Lights up* when detecting intrusion Continuously blinks in the event of cover monitor error Continuously lit in the event of alignment position error Continuously blinks in the event of self diagnosis error Continuously lit in the event of power voltage error Continuously blinks in the event of long-term diagnosis error Continuously blinks in the event of Anti-masking error (*ON/OFF selectable using the mode selector)
Memory LED	Red LED : Blinks for 3 minutes during memory display, Auto reset operation either of continuous lighting for 47 minutes or blinking for 50 minutes selectable (Blinks to lights/blinks, ON/OFF selectable using the mode selector)
Functions	Sensitivity selection Operation mode selection Alarm memory LED Self diagnosis Low voltage monitoring Temperature compensation LED area checker Front & back tamper Environmental adjustment Creep zone detection Walk test mode Near area cancellation Long-term diagnosis Anti-masking
Installation height	6.6’ to 20’(2.0 to 6.0m) (varies depending on the operation mode) • Low position mode : 6.6’ to 9’(2.0 to 2.7m) • High position mode : 9’ to 11.5’(2.7 to 3.5m) • Pet mode : 8.3’ to 10’(2.5 to 3.0m) • High density mode : 6.6’ to 20’(2.0 to 6.0m)
Area angle adjustment range	Horizontal direction :±45° (in 5° steps) Vertical direction :17° (no stage adjustment)
Ambient temperature range	-25 to +55˚C (no condensation and freezing)
Mounting position	Indoor/outdoor wall surface * Can be mounted on poles and ceilings (or under eaves) using optional accessories
IP rating	IP55
Connections	Terminals (M2.6 self up terminal)
Weight	Approx. 600g
Appearance	Body:Resin (gray), Window:Resin (white)